Target Vision Security Systems

• Support for up to 508 points on two analog addressable loops
• Built???in Ethernet connector for web???browser based programming and ConettixIP Alarm-over-IP communication
• Carbon Monoxide Detector (gas) support meets NFPA 720 (2009) requirements for visual and audible annunciation
• Auto???Learn mode for easy provisioning
• On???line help and off???line programming capability provide simple configuration and service.

Trouble conditions. The built???in keypad can be used for total system control and programming even when wearing fireman gloves. In addition, a large 4???line by 20???character alphanumeric LCD display shows programmed device point information. Four keys enable Drill, Reset, Silence, and Acknowledge functions.

The FPA???1000???UL enables various programming approaches:

• Two different phone or IP numbers
• Different dialing types for PSTN (pulse only, tone and pulse, or tone only)
• Individual PSTN line supervision (audible and visual trouble signal in the case of a transmission path failure)
• Selectable options for Report Steering Groups
• Programmable acknowledge wait time for each IP reporting Conettix account (15 sec up to 255 sec)
• Test call frequency individually programmable for each account (4, 12, 24 hour, 7 and 28 day intervals, standard frequency 24 hour)

Notification Appliance Circuits (NACs):

• Two Class A Style Z or Class B Style Y NACs provide up to 4 A of 24 V power (non-synchronized: 2.5 A per NAC; synchronized: 2.75 A NAC 1 + NAC 2 in total) to operate horns, strobes, bells, and other notification appliances. Each NAC can be programmed to provide Temporal Code 4, Temporal Code 3, and steady, puls- ing, and synchronized protocol output for Wheelock, Gentex, and System Sensor notification appliances.

Signaling Line Circuits (SLCs):

• The FPA???1000???UL Fire Panel uses the patented DCP Digital Communication Protocol to communicate with each of the analog addressable devices located on the SLCs. This fast and reliable protocol allows the use of standard non???twisted, non???shielded wiring for the SLCs. The FPA???1000???UL supports two Class B, Style 4 or one Class A, Style 6 or 7 per SLC.

Mounting Considerations:

• The cabinet can be either semi-flush (requires optional FPM???1000???SFMK Semi-flush Mounting Kit) or surface mounted.
• Depending on the configuration and the battery selection, the FPA???1000???UL can be quite heavy. When attaching the enclosure to a surface, use mounting hardware (not supplied) capable of supporting this weight, and reinforce the wall as necessary.

Wiring Considerations:

• The length of wire allowed between the control panel and the last device on a wiring run depends on the current drawn on that wiring run. Reducing the number of devices on a wiring run allows the individual runs to be longer.

Additional Information:

• Item Code: FPA1000UL

Additional Information:

• Production Capacity: Minimum: 24 VDC, 7 Ah Maximum: 24 VDC, 18 Ah

• Smoke threshold is adjustable and automatically compensated
• Rotary switch addressing
• Flexible work modes determined by the control panel
• Selectable base locking mechanism prevents malicious removal of the detector
• Multi???criteria or multi???sensor technology reduces false alarms

Functions:

Address Range:

• The FAP???440 Analog Detectors have a valid address range from 1 to 254 which is set by rotary switches on the back of each detector.

Indicator LED:

• The detector head has a multi???color LED to indicate status. To verify power to the detector and functioning communication of the analog addressable loop, the LED indicator flashes green when operating normally (polling). Through panel parameter setting, it is possible to turn on or off operation of the polling indicator. In the event of an alarm condition, the detector LED will always show a steady red light.

Modular Construction:

• These detectors are part of a two???piece modular design for detector assemblies. An FAP???440 Analog Detector attaches to an FAA???440 Family base. The base’s security locking tab prevents any unauthorized detector removal from the base.

Multi???sensor detector:

• The multi???sensor detector contains a photoelectric smoke sensor and a heat sensor. Either sensor can detect a fire and activate an alarm signal. The smoke threshold is adjustable (see Sensitivity Calibration and Compensation below) while the heat sensor’s threshold is set at 135°F.

Multi-criteria detector:

• The multi???criteria detector also contains smoke and heat sensors that work independently of each other, but in conjunction with the CO sensor. In this model, an alarm signal will be activated by either one or both of the sensors only if the CO level is also exceeded.

Programming:

• Local programming is carried out at the panel keypad or by computer through a Web browser. Remote programming is carried out through a Web browser.

Sensitivity Calibration and Compensation:

• The sensitivity of the smoke sensor is programmable with 12 levels from which to choose. Throughout its normal life cycle, the smoke detector monitors itself against its factory calibrated level and periodically compensates itself to keep the sensitivity at it programmed level. When the detector is excessively contaminated, this condition will be annunciated at the control panel.

The following wire gauges were tested and approved:

• Selectable Fixed Temperature threshold
• Rate-of-Rise feature can be switched on or off
• Selectable base locking mechanism prevents malicious removal of the detector

• The detector has a valid address range from 1 to 254 which is set by rotary switches on the back of the detector.

• The detector head has a multi???color LED to indicate status. To verify power to the detector and functioning communication of the analog addressable loop, the LED indicator flashes green when operating normally (polling). Through panel parameter setting, it ispossible to turn on or off operation of the polling indicator. In the event of an alarm condition, the detector LED will always show a steady red light.

• The detector is part of a two???piece modular design for detector assemblies. A detector attaches to a base in the FAA???440 Analog Standard Base or Analog Isolator Base family. The base’s security locking tab prevents any unauthorized detector removal from the base.

• Local programming is carried out at the panel keypad or by computer through a Web browser. Remote programming is carried out through a Web browser.

• The detector has an alarm threshold temperature range of +135°F to +194°F (+57°C to +90°C) with 17 possible settings. The rate-of-rise feature can be switched on or off.

Mounting Considerations:
Detectors are typically mounted on the ceiling. However, if detectors are mounted on a wall, they must be at least 4 in. (10.2 cm), but no more than 12 in. (30.5 cm), below the ceiling. When other devices containing magnets or producing magnetic fields (for example, loudspeakers) are present in the area, the base must be at least 1 ft (30 cm) from these devices to prevent unwanted activation of the test switch.

Remote Indicator:

• If a remote indicator is used in the circuit, it must be no more than 10 ft (3 m) from the base.

Additional Information:

• Item Code: FAH-440

• General Description
  
  
  • The FLM???420???O1I1 Output-input Interface Modules are fitted with one output to control external devices and with one monitored input
  • with 1 open collector output and 1 monitored input, in-built version

   

   

   

  
  
  

• Features
  
  
  • Semi-conductor output electrically isolated from LSN loop and short-circuit proof
  • Max. switchable current per output 700 mA
  • Individually selectable input monitoring functions (EOL or contact)
  • Maintains LSN loop functions in the event of wire interruption or short-circuit thanks to two integrated isolators

  
  
  
  

• Data Sheet
  
  

  Download

  FLM-420-O1I1-E Output-input interface module in-built

   

   

• Specification
  
  

  LSN
  LSN input voltage	15 V DC to 33 V DC
  Max. current consumption from LSN	1.9 mA
  Output
  Max. switchable voltage of semi-conductor output	30 V DC
  Max. switchable output current	700 mA (depending on power supply)
  External power supply	5 V DC to 30 V DC
  Input
  Line monitoring with EOL
  EOL resistor	Nominal 3.9 k???
  Overall line resistance RΣ with RΣ = RL/1 + RL/2 + REOL	Standby: 1500 ??? to 6000 ??? Short circuit: < 800 ??? Line interruption: > 12.000 ???
  Contact monitoring
  Max. current strength (current pulse)	8 mA
  Minimum activation time of the input	3.2 s